Experimental PC

From Applied Optics Wiki
Revision as of 11:08, 5 November 2008 by Sds (talk | contribs)

Jump to: navigation, search

Back to Linux How-tos

Extra stuff for all the hardware in blanket & pouffe, the ARRO-SAM PC & OSAM

In December 2007 I upgraded blanket, the PC used to control the ARRO-SAM experiment, to the current version of openSuSE (10.3 when this page was first written, now 11.0). This PC had been running Redhat 9 for a number of years and due to heavy use as an experimental PC and reasonable stability, it had not been updated. Redhat 9 runs a 2.4 kernel, so there were some extra things to do with the drivers and compiling c-scan.

Addition (April 2008): Rob upgraded pouffe in the O-SAM lab, pretty much the same as blanket accept for ISA PI stages

The information contained here will also be useful if you want to install any of these bits of hardware on any other Linux PC.

Pre-install

Scenario 1: inherited PC with working hardware, updating Linux

  1. Make a list of all the hardware you have (or likely to have) attached to the PC
  2. From this list, work out which programs/utilities you use
    • Most of these will already be installed in /usr/local/bin/
  3. Work out how to recompile (and re-install) all these programs
    • Most will have their source code in /home/scan/source/hardware/
  4. Save all the configuration files you think you might need
    • Most of these will be in /etc/

Example: updating blanket from RdeHat 9 to SuSE 10.3:

I tarballed /etc/ and /usr/local/bin/ and stuck the files in my home directory where they would be recoverable after new install. The aim was to retain the old root partition of the old (Redhat 9) system, to enable it to be mounted by the new (SuSE 10.3) system under /old_redhat_9_root/ but since installation involved resizing the old partition (always potentially problematic) it's a good idea to backup anything you think you might need. /etc/ for configuration files (including our own, for the stages, the SLM etc) and /usr/local/bin/ just as a reminder of the extra stuff (mainly our own) that we installed.

In the event, the old root partition wasn't wiped, and I was able to grab the files from there (/old_redhat_9_root). After the install, I copied the files I'd actually needed to /home/share/backup_system_files/blanket/

Scenario 2: Adding new hardware to an already up-to-date PC

  1. Use this wiki, find the instructions for the relevant hardware
  2. Any extra configuration files you need (e.g. /etc/stages/IW_stage_origin) - copy off a PC that already has this hardware installed (or you may find a copy in /home/share/backup_system_files/<name of PC> )


Install

I had to resize the old partition as it was taking up all the disk (except for the swap partition). I resized the old partition to 20GB (it had 15GB of stuff in it) and made a new 30GB root partition. I also extended the swap to 4GB.

Other than that I just did a standard install, then performed the standard local configuration stuff as with any other PC.

The resizing of the old partition was successful and I was able to copy the files I needed directly from /old_redhat_9_root/etc/

Scope (and AFG) utilities

These are the standard command line utilities to grab traces, save setups etc

vxi11

(Used by Agilent and Tek utilities, and a low-level diagnostic tool in its own right)

  • cd /home/scan/source/hardware/vxi11/
  • make clean; make; sudo make install
  • Installs:
    • vxi11_cmd

Agilent scope

  • cd /home/scan/source/hardware/agilent_scope/
  • make clean; make; sudo make install
  • Installs:
    • agetwf
    • agilent_load_setup
    • agilent_save_setup

Tek scope/AFG

  • cd /home/scan/source/hardware/tek/
  • make clean; make; sudo make install
  • Installs:
    • tgetwf
    • tek_load_setup
    • tek_save_setup
    • tek_afg_upload_arb

LeCroy scope

  • cd /home/scan/source/hardware/ethernet_scope/
  • make clean; make; sudo make install
  • Installs:
    • eth_cmd
    • /etc/lecroy_tcp/ (empty directory)
  • cd /home/scan/source/egetwf/
  • make clean; make; sudo make install
  • Installs:
    • egetwf

PI PCI stage driver

  • cd /home/scan/source/dev/pi_pci/driver_2.6/library/
  • make clean; make; sudo make install
  • Installs:
    • pi_save_pos
    • pi_recall_pos
    • (pi_user library)
    • /etc/pi_stage/stage_database/
  • cd /home/scan/source/hardware/pi_pci_stage/
  • make clean; make; sudo make install
  • Installs:
    • set_stages_safe
    • manual_pci_stage (manual_stage)
    • /etc/pi_stage/position_um if it doesn't already exist (default stage position file, all axes at 0)
    • /etc/pi_stage/installed_stages - this is the default list of installed stages, which you may need to edit if yours are different:
axis 0  m-531.dd
axis 1  m-531.dd
axis 2  m-605.2dd
axis 3  m-605.2dd
  • cd /home/scan/source/dev/pi_pci/driver_2.6/driver/
  • make
  • sudo ./install_pi_stage_recall
  • Installs:
    • PI PCI stage device driver

PI ISA stage

  • cd /home/scan/source/hardware/stages
  • make -f Makefile.osam clean; make -f Makefile.osam;
  • sudo make -f Makefile.osam install
  • Installs:
    • manual_stage
    • /etc/stages/PI_stage_origin if it doesn't already exist (default stage position file, all axes at 0)

Inchworm and IDAC stages

  • cd /home/scan/source/hardware/IW_driver
  • sudo make install
  • Installs:
    • /etc/stages/IW_stage_origin if it doesn't already exist (default stage position file, both axes at 0)
  • cd /home/scan/source/hardware/IDAC_driver
  • sudo make install
  • Installs:
    • /etc/stages/IDAC_stage_origin if it doesn't already exist (default stage position file, both axes at 0)

BNS SLM

  • cp -av /old_redhat_9_root/etc/slm /etc/
  • cd /home/scan/source/dev/BNS/driver_2.6/
  • make
  • sudo ./install_slm_mtrr
  • Installs:
    • BNS SLM device driver
  • cd /home/scan/source/dev/BNS/utils/
  • make clean; make; sudo make install
  • Installs:
    • bns_change_frame (change_frame_bns)
    • bns_laser_ab
    • bns_power
    • bns_power_off
    • bns_power_on
    • bns_upload_frame (upload1_bns)
  • cd /home/scan/source/hardware/bns_slm/manual_bns/
  • make clean; make; sudo make install
  • Installs:
    • manual_bns
  • cd /home/scan/source/hardware/bns_slm/set_bns/
  • make clean; make; sudo make install
  • Installs:
    • set_bns

FFTW libraries

These are needed by the higher order correction algorithm when using the SLM in c-scan. I use the float version of the libraries (rather than the standard double version) for speed, and so an extra option must be set before compiling.

  • cd /home/scan/source/fftw-3.0.1_blanket/
  • make distclean; ./configure --enable-float; make; sudo make install
  • Installs:
    • (FFTW float libraries)

Comedi, specifically the Amplicon PCI230 DAQ

The current version of the comedi is 0.7.75. The current version of comedilib is 0.8.1.

comedi

  • cd /home/scan/source/hardware/comedi/comedi-0.7.75/
  • make distclean; ./configure; make;
  • sudo make install; sudo /sbin/depmod -a; sudo make dev
  • Installs:
    • (comedi libraries)
    • (device libraries)
    • (comedi devices in /dev/)
  • sudo echo 'KERNEL=="comedi*", MODE="0666"' > /etc/udev/rules.d/53-comedi.rules
    • Sets the permissions of the DAQ to world-readable-and-writable during boot
  • sudo echo 'install amplc_pci230 PATH=/sbin:/usr/sbin:/usr/local/sbin:$PATH; comedi_config /dev/comedi0 amplc_pci230' >> /etc/modprobe.conf.local
    • Means that when you use modprobe to load the amplc_pci230 module, it automatically runs comedi_config too.
    • Unfortunately, udev ignores this, so we have to...
  • sudo echo '/sbin/modprobe amplc_pci230' >> /etc/init.d/boot.local
  • sudo echo '/usr/local/sbin/comedi_config /dev/comedi0 amplc_pci230' >> /etc/init.d/boot.local
    • Makes the PCI230 modules get loaded automatically at boot time

Dealing with kernel updates

Updates to the kernel mean that the comedi drivers need to be reinstalled. As the kernel updates are usually fairly minor, the comedi drivers usually don't need recompiling. It's annoying having to deal with this, so this solution helps to remove some of that annoyance. When you've installed comedi run the following as root:

cp -r /lib/modules/$(uname -r)/comedi /lib/modules/

This will copy your current comedi installation to /lib/modules/comedi.

Now add the following to /etc/init.d/boot.local (*before* any of the commands to load the comedi modules):

KERNEL=$(uname -r)

if [ ! -d /lib/modules/${KERNEL}/comedi/ ]; then
        cp -r /lib/modules/comedi /lib/modules/${KERNEL}/
        depmod -a
fi

This will check for the presence of the comedi directory in the modules directory for the current kernel and copy it over if it doesn't exist. depmod -a updates the module dependencies.

It is important that if you install a newer version of comedi that you remove /lib/modules/comedi and replace it with your updated version. Also note that some kernel updates may be incompatible with your compiled comedi drivers and so you'll have to recompile and reinstall using the instructions above.

comedilib

  • cd /home/scan/source/hardware/comedi/comedilib-0.8.1/
  • make distclean; ./configure; make; sudo make install
  • Installs:
    • libcomedi
    • comedi_test
    • /usr/local/sbin/comedi_config

Comedi Settings for the NI PCI-6251

If you want to use the PFI port as a digital output, you must do some extra configuration. This is possible using the demo tools in comedilib (which could also be copied across to your own code of course). So, to change channel 14 of subdevice 7 (ie. pin 1 on the connector) to be a digital output do the following in the comedilib/demo directory:

  • ./choose_routing -s7 -c14 16 # NI_PFI_OUTPUT_DO == 16
  • ./dio -s7 -c14 1 # now its an output
  • ./outp -s7 -c14 1 # test the output (or 0)

c-scan

I had to make a once-only change to blanket's c_scan Makefile, due to going from a 2.4 kernel to a 2.6 kernel (and subsequent change of BNS device driver).

  • cd /home/scan/source/hardware/scanner/
  • make clean; make; sudo make install
  • cp ~sds/bin/cscan /usr/local/bin/
  • Installs:
    • c_scan
    • c_scan man pages
    • cscan: this performs a "touch" on the con-file that you're running with c_scan, so you can see the time at which you started the scan, and - by the time stamp on the data file - the time at which you finished the scan.

Jai CCD camera

  • cp ~sds/bin/ccd* /usr/local/bin/
  • Installs:
    • ccd_set_serial
    • ccd0
    • ccd1
    • ..
    • ccd7 (different shutter speeds)