Difference between revisions of "3d printing"
(Created page with "The Fab Lab has a Makerbot Replicator 2 for 3D printing using PLA plastic. ==Training== The replicator 2 is a relatively easy and straightforward machine to use. BUT please ask ...") |
(→Typical workflow (how to design and print something)) |
||
| Line 32: | Line 32: | ||
In OpenSCAD design an object - this is done by writing a little program to describe it. This is very easy and very efficient, eg. | In OpenSCAD design an object - this is done by writing a little program to describe it. This is very easy and very efficient, eg. | ||
| − | < | + | <pre> |
$fn=50; | $fn=50; | ||
difference(){ | difference(){ | ||
| Line 54: | Line 54: | ||
translate([-15,-15,-21])cylinder(h=10,r=3,center=true); | translate([-15,-15,-21])cylinder(h=10,r=3,center=true); | ||
} | } | ||
| − | </ | + | </pre> |
Revision as of 18:27, 9 June 2013
The Fab Lab has a Makerbot Replicator 2 for 3D printing using PLA plastic.
Contents
Training
The replicator 2 is a relatively easy and straightforward machine to use. BUT please ask someone who has used it before to show you how before trying it.
Prerequisites
The printer is set up only to accept files in .x3g format supplied on an SD card. If you want to print some other way forget it. Since most instructions will assume you print from makerware from a computer directly attached to the print please follow these instructions carefully (else you can bugger the printer).
Software
Please install the follow bits of software on your computer - they all run on all platforms (Windows, Mac and Linux) and all have reasonable instructions for installation. I have only tested on linux from kubuntu, YMMV.
OpenSCAD
This is a really nice bit of software for designing 3D objects. You use it be writing a very simple program to describe your object. Once you are happy you export to a .STL file which describes your object. OpenSCAD is in kubuntu repositories
ReplicatorG
This will take the .STL file and produce .gcode and .x3g code. The .gcode is basically the generic instructions for printing the object. The .x3g is a specific translation of the gcode for the 3D printer. ReplicatorG can be obtained here: http://replicat.org/
ReptierHost
This is useful for viewing the .gcode instructions to make sure you are happy with the internal structure of the object you're designing. RepetierHost can be downloaded here: http://www.repetier.com/download/
Makerware
This is makerbot's own system - I haven't tried it.
Typical workflow (how to design and print something)
In OpenSCAD design an object - this is done by writing a little program to describe it. This is very easy and very efficient, eg.
$fn=50;
difference(){
// the cube
minkowski() {
cube([38,38,38],center=true);
// rounded corners
sphere(r=1,$fn=10);
}
// the stuff we remove
rotate([0,0,0])cylinder(h=50,r=15,center=true);
rotate([90,0,0])cylinder(h=50,r=15,center=true);
rotate([90,0,90])cylinder(h=50,r=15,center=true);
translate([15,15,21])cylinder(h=10,r=3,center=true);
translate([-15,15,21])cylinder(h=10,r=3,center=true);
translate([15,-15,21])cylinder(h=10,r=3,center=true);
translate([-15,-15,21])cylinder(h=10,r=3,center=true);
translate([15,15,-21])cylinder(h=10,r=3,center=true);
translate([-15,15,-21])cylinder(h=10,r=3,center=true);
translate([15,-15,-21])cylinder(h=10,r=3,center=true);
translate([-15,-15,-21])cylinder(h=10,r=3,center=true);
}
